# One TV Frozen or Pixelated in Your Bar While the Others Work

> When one TV freezes or pixelates and the rest look fine, the cause is usually local to that screen: its TV input, its cables, its receiver or the coax feeding it. Start with checks that touch only that screen. Save anything shared, such as the SWiM Power Inserter, for a quiet moment or a call to support.

Source: https://www.sportsdirectllc.com/help/troubleshooting/one-tv-frozen-pixelated-bar · Troubleshooting · Last reviewed 2026-10-10 · Sports Direct | DLM Media

## Why one screen fails while the rest keep playing

When you have one TV frozen or pixelated in your bar and every other screen is fine, the dish and the weather are rarely to blame. Those feed every receiver, so they tend to take the whole room down at once. A single bad screen points to something only that screen uses: the TV itself, its input setting, the HDMI cable, its receiver, or the coax run to that receiver. That narrows the search and means most fixes can be done without touching the screens guests are watching.

If several screens or all of them are failing, this is the wrong page. Use the [no-signal-on-every-TV triage](/help/troubleshooting/no-signal-on-every-tv) instead, because the cause and the order of steps are different.

## The 60-second triage mid-service

Before you touch a cable, answer three questions with the remote:

1. **Does the guide open?** Press GUIDE. If the guide appears and moves, the receiver is alive and the problem is the picture reaching it. If nothing responds, the receiver is probably locked up.
2. **Is it every channel or just one?** Change to two or three channels. If only one channel is broken, it is likely a channel-side issue, not your equipment.
3. **Is there a message or code on screen?** Write it down exactly. Error 775, for example, has its own fix path in our [Error 775 guide](/help/error-codes/error-775).

> **Tip:** If the room is full and the broken screen is showing a game people care about, put that game on a working screen nearby first. Fix the problem screen once guests are taken care of.

## What the symptom tells you

| What you see | Likely meaning | Go to |
| --- | --- | --- |
| Guide works, picture breaks up on all channels | Weak or interrupted signal to that receiver | Steps 3 and 4 |
| Nothing responds, image stuck | Receiver locked up | Step 2 |
| Picture fine on some channels, broken on one | Channel-side issue | Wait, then call if it persists |
| Blank screen or "no input" from the TV | TV input or HDMI problem | Step 1 |
| On-screen error code | Specific fault | Look up the code in [error codes](/help) |

## Fix it in order, least disruptive first

Each step affects only the problem screen until step 6. Stop as soon as the picture comes back.

### 1. Check the TV side

Confirm the TV is on the right input. Reseat the HDMI cable at both the TV and the receiver, and look for a kinked or crushed cable behind the mount. If you have a spare HDMI cable, swap it in. A picture that returns after a swap means the old cable was the problem.

### 2. Restart that one receiver

Unplug only the problem receiver's power cord, wait a moment, and plug it back in. Give it a few minutes to boot fully before you judge the result. If the screen comes back clean, it was a lockup. If it locks up again later the same day, note the time and mention it when you call.

### 3. Tighten the coax on that receiver

On DIRECTV systems, the connections should be snug, finger-tight, at every point the signal passes through. For a single screen, start with the SAT-IN coax on the back of the receiver and the wall plate where the cable comes out. Do not overtighten with tools. A loose connector here is one of the most common reasons one screen pixelates while its neighbors look fine.

### 4. Ask the receiver what it sees

On the RC73 remote used with commercial receivers, pressing DASH shows the receiver ID, the satellite signal type (SWiM or Multiswitch) and internet status. Jot down the last six digits of the ID. Support will want it, and the signal type tells a technician how that receiver is wired.

### 5. Think about recent changes

Was the TV or receiver moved during a remodel or a furniture shuffle? Moving equipment back to its previous location often restores service. If you want it to stay in the new spot, it may need a technician to rewire it properly. Our notes on [moving business TV service](/faq/move-business-tv-service) cover what a relocation involves.

### 6. Power-cycle the SWiM Power Inserter (quiet hours only)

The SWiM Power Inserter is a small black or gray box, about the size of a brick, with two coax cables attached. Its power cord may carry a green sticker that says Do Not Disconnect. In many installations it supports the single-wire network that several receivers share, so cycling it can briefly interrupt other screens. Only do this when the room is quiet, or when the problem screen shows Error 775.

1. Unplug the inserter from the outlet and wait until the green light fades out completely, which can take up to 30 seconds.
2. Plug it back in and wait 30 seconds for it to restart.
3. Confirm the green light is back on and steady, then check the TV.

If the light will not return to steady green, check the outlet. Move it from a power strip directly into a wall outlet, and never use an outlet controlled by a wall switch, because the inserter has to stay powered at all times. Our page on [SWiM Power Inserter lights](/help/led-guide/swim-power-inserter-lights) explains what each light state means.

> **Warning:** If other screens drop after the power cycle and do not come back once the inserter shows steady green, stop and call support rather than unplugging more equipment.

## When to stop and call

Call support when any of these is true:

- You have worked through steps 1 to 5 and the screen is still frozen or breaking up.
- The same screen fails repeatedly over several days, even after it recovers.
- A coax connector, wall plate or cable is visibly damaged.
- The fault is spreading to other screens.

Have the screen location, the receiver ID digits, any error code and the steps you already tried. That lets a technician skip the basics. Customers can reach General Support at 480-941-3703. Gaming venues can use Gaming Support at 877-659-9257.

If one screen keeps acting up, a walk-through of every receiver, cable run and outlet can catch weak points before game day. Our [business TV audit checklist](/guides/business-tv-audit-checklist) is a good starting point, and our [installation and support services](/services) cover the fixes that need a technician.

## Frequently asked questions

### If a storm causes pixelation, why is only one of my TVs affected?

Weather usually affects every screen fed by the same dish, because they share the same signal from the sky. If only one screen breaks up during a storm while the rest look fine, the storm is probably a coincidence. Check that screen's coax connections, its receiver and its HDMI cable first. If more screens start failing as the weather worsens, switch to the all-screens triage instead.

### Is it safe to unplug the SWiM Power Inserter during a busy shift?

It is not dangerous, but it is disruptive. The inserter often supports equipment that several receivers share, so cycling it can briefly drop other screens, including the ones guests are watching. During a rush, move the important game to a working screen and handle single-screen checks only. Leave the inserter for a slow period, or for when the problem screen shows Error 775 and nothing else has worked.

### How do I tell whether the TV or the receiver is the problem?

Press GUIDE. If the guide appears normally but the picture behind it is broken, the receiver is running and the issue is usually the signal reaching it. If the TV shows no input or nothing at all, test with a spare HDMI cable or connect the receiver to a different TV briefly. If the picture looks fine on another TV, the original TV or its input is the likely culprit.

### What should I have ready before calling support about one screen?

Note which screen it is and where it sits, any error code exactly as shown, and the last six digits of the receiver ID, which appear when you press DASH on the RC73 remote. List what you have already tried, such as restarting the receiver or tightening connections, and whether the problem comes and goes. That detail helps a technician narrow the cause quickly and avoid repeating steps.

## Sources

- [Get help with DIRECTV error code 775](https://www.directv.com/support/article/000080603), DIRECTV
- [directv.com](https://www.directv.com/dtvassets/sales/directv/upper_funnel/business/2024/pdf/3313677-tips-tricks-bars-and-restaurants.pdf), DIRECTV

Talk to a specialist: 888-688-1699 (New Sales) or https://www.sportsdirectllc.com/contact