Sports Direct | DLM Media
Table with chairs placed in living room with comfortable couch and TV near kitchen zone with cupboards in stylish apartment
Guide · Bars & sports bars

How to Hide TV Wires on a Brick Wall in Bars and Restaurants

On exposed brick you rarely hide TV wires completely; you decide how they show. Cut what runs to each screen first, then choose a painted raceway, exposed conduit treated as a design line, a ceiling drop or a through-wall route, anchored in mortar joints so the brick stays intact.

Reviewed November 15, 2026 9 min readBy Sports Direct | DLM Media
On this page

Who This Is For and What You Can Decide

Exposed brick, painted block and bare concrete give many bars and restaurants their character. They are also the hardest surfaces in the building to run cable on, because you cannot fish a wire through them the way you can through drywall. If you want to hide TV wires on a brick wall, you usually cannot make them disappear completely. You can decide how they show up, and whether a guest ever notices them.

This is for owners, general managers and facilities leads running industrial-style rooms: a converted warehouse taproom, a brick-walled bistro, a brewpub with open ductwork and a polished concrete floor. You should come away able to pick a cable route for each wall, weigh raceway against exposed conduit against a ceiling drop, and walk into a site survey with the right questions.

If your walls can still be opened, the job is different; see restaurant TV wiring before drywall. For plaster, mixed surfaces and the broader retrofit picture, read TV wiring in an older building. This page stays on the surfaces you have chosen to leave exposed.

Start by Shrinking What Has to Run to Each Screen

The neatest cable run is the one you never install. Before choosing a cover, count what each screen actually needs.

A bar TV needs power and a video signal. Clutter creeps in when each screen also gets its own receiver, a power strip, a remote sensor and a coil of spare cable tucked behind it. On drywall that mess hides in a recessed box. On brick, every extra box is another cord to route and another thing a guest sees from a bar stool at an angle.

Ways to trim it down:

  • Centralize the receivers. Putting receivers in a rack behind the bar, in a back office or in a closet means each screen needs one signal cable plus power, not a stack of gear. Staff also change channels without reaching behind a TV during a rush.
  • Bring power to the screen. A licensed electrician can often add an outlet at mount height, fed by its own conduit, so no cord hangs down to a floor outlet. What is allowed and how it must be done depends on local code, so that decision belongs to the electrician.
  • Group screens on shared runs. Three TVs on one brick wall can share a single horizontal run near the ceiling with short vertical drops, instead of three full-height runs.
  • Leave spare capacity. While a raceway or conduit is being installed, pulling one extra cable takes little effort and saves reopening the run when you upgrade a screen.

Ways to Hide TV Wires on a Brick Wall, Compared

Most rooms end up using two or three of these, matched to each wall.

OptionHow it looksImpact on the masonryBest fit
Paintable surface racewaySlim channel on the wall surfaceFasteners into mortar jointsPainted brick, block or smooth concrete
Exposed metal conduitDeliberate metal line, painted or bareStraps anchored into mortarRooms with existing exposed pipe and steel
Ceiling dropCable comes straight down from aboveLittle or none on the wallOpen joists, ductwork, high-mounted screens
Through-wall from back of houseNothing visible on the guest sideOne small hole behind the screenWalls backed by a kitchen, office or storage
Columns, beams or millworkRun hidden behind wood or shelvingNone on the brickBack bars, wrapped columns, built-ins
Chasing a channel into masonryCable buried and patched overPermanent cuttingLast resort, with owner approval

Paintable surface raceway

Raceway is the familiar restaurant TV cord cover: a low-profile channel that fastens to the wall and snaps closed over the cable. It is quick to install, and the covers come off for service. The catch on brick is texture. A flat channel bridges the high points and leaves shadow gaps over the low ones, which looks fine on painted block and less convincing on rough, old brick. Brick is also several colors at once, so painting a raceway brick red rarely works. Paint it to match the mortar, or pick a color that clearly contrasts and own it.

Exposed conduit as a design line

In a room that already shows sprinkler pipe, steel window frames or black light fixtures, metal conduit can read as part of the architecture rather than a fix. The rule is discipline: plumb verticals, level horizontals, tight square bends and a finish that matches the other metal in the room. Done that way, an exposed brick TV mount with its wires in conduit looks intentional. Done casually, it looks like an afterthought. It takes more labor than raceway and is harder to change later, so it suits screens that will stay put.

Ceiling drops and pole mounts

Industrial rooms often have open ceilings, which is a gift. Cable can run along joists or ductwork painted a dark color and drop straight down behind the screen, so only a short vertical section is visible. If the screen hangs from a ceiling mount, the cable can often run inside the pole and not touch the wall at all. Ceiling mounting needs a check of what the structure can carry and how the screen sits in the room's sightlines.

Through the wall from behind

When a kitchen, office or storage room sits behind the brick, one small hole directly behind the screen can hide everything on the guest side, with the run continuing where looks matter less. Ask before drilling: the landlord may need to approve it, and some walls between a kitchen and other spaces may have fire-separation considerations that an installer or contractor should confirm. Kitchen-side runs should also be kept clear of heat and grease.

Columns, beams and back-bar millwork

The back bar is often the best hiding place in the room. Shelving, cabinetry, wood-wrapped columns and beams can carry cable out of sight, then hand it off to a short visible drop. For screens along the rail or in booths, see these owner questions on TVs in restaurant booths and along the bar rail.

Chasing a channel into the masonry

Cutting a groove into brick or mortar, laying cable in it and patching over it hides the run completely. It is also permanent, dusty, hard to undo and frequently ruled out by a lease or a building's historic status. Treat it as a last resort and only with written approval from whoever owns the wall.

A Decision Checklist for Each Wall

Walk the room and answer these for every wall that will carry a screen.

  1. Can the masonry be altered at all? Check the lease and any historic restrictions. If drilling is off the table, look first at ceiling drops, pole mounts and millwork.
  2. What is above the screen? An open ceiling usually makes a top-down drop the shortest and least visible route.
  3. What is on the other side? Back of house behind the brick points toward a through-wall route.
  4. What finishes already exist? Exposed pipe and black steel make conduit a natural choice. Clean painted walls suit raceway.
  5. How rough is the surface? Painted block and smooth concrete take raceway well. Rough, uneven brick favors conduit standing slightly off the wall or a ceiling route.
  6. Where are the receivers and power? A central rack and outlets at mount height shrink every other decision.
  7. How often will this screen change? Screens you expect to move or upgrade need routes with removable covers, not buried cable.
  8. What is the environment? Kitchen heat, grease near the pass, and moisture on a patio wall all affect which materials hold up.

If you are planning a sports-forward room with many screens versus a dining room with one or two, the cable approach shifts too; this comparison of sports bar versus casual restaurant TV setups covers that broader layout decision.

Common Mistakes on Exposed Brick and Concrete

Most bad-looking installs come down to a handful of avoidable choices.

  • Sticky-back cord covers on raw brick. Adhesive does not grip a rough, dusty surface for long. The cover sags and pulls loose during a cleaning.
  • Drilling into the brick face. Anchoring in mortar joints is generally easier to repair later, since mortar can be repointed. A cracked or chipped brick face is hard to hide.
  • Wandering runs. Diagonals, gentle curves and runs that jog around a light fixture draw the eye straight to the cable. Straight, square lines disappear into the room's geometry.
  • Trying to match brick color. Brick varies from unit to unit, so a single paint color looks wrong next to most of them. Match the mortar or contrast on purpose.
  • Hanging slack and power bricks. A loop of extra cable or a power adapter dangling below the screen is visible from every low seat. Secure them behind the mount or move them to the rack.
  • Burying everything with no access. If a cable fails or a screen moves, someone has to get to it. Sealed-in runs turn a quick swap into a construction job.
  • Lumping power and signal together. Whether power and low-voltage cable can share a channel, and with what separation, depends on the product and local code. Let the electrician decide rather than improvising.
  • Forgetting the bottom end. A tidy vertical run that ends at a floor outlet across a walkway leaves a cord where servers walk.

What to Ask Your Installer Before Anyone Drills

The right questions up front tell you whether a provider will treat your walls with care.

  • Will you survey the room in person and show me the planned route on each wall before work starts?
  • How do you anchor into brick and concrete, and how do you patch if we move a screen later?
  • Who handles power? Do you coordinate with a licensed electrician, or do I need to hire one separately?
  • Where will the receivers live, and how many cables will run to each screen?
  • Can I see finish samples, or photos of raceway and conduit work in similar rooms?
  • Will you leave spare capacity in each run for future screens or upgrades?
  • Can the install happen around our service hours so we are not drilling during lunch?
  • If we have more than one location, can you apply the same standard at every site?

Cable routing works best when it is settled while the screens are being planned, not improvised on install day. Whoever you talk to about commercial TV installation for restaurants, ask to see each screen, its receiver location and its cable path discussed together, so the choices on one wall do not create problems on the next. Sports Direct, an authorized commercial dealer, provides programming through commercial TV for business alongside equipment and installation, coordinated from Phoenix, AZ, with technicians and engineers in all 50 states.

If you are weighing options for a brick-walled bar or dining room, talk with a programming specialist about what fits your space.

Common questions

Answers to what people ask

Not reliably. Adhesive needs a smooth, clean surface, and raw brick is rough, porous and often dusty. Covers stuck to brick tend to sag or peel, especially near a kitchen or an entry where temperature changes. On brick, fasten raceway mechanically into the mortar joints, or choose conduit with proper straps. Adhesive can work on smooth painted block or sealed concrete, but even there mechanical fasteners hold up better in a busy room.

It depends on execution. Conduit reads as intentional when every run is plumb and level, bends are tight and square, and the finish matches other metal in the room, such as light fixtures, shelving brackets or window frames. It looks unfinished when it wanders, mixes finishes or stops awkwardly short of the screen. Ask your installer to sketch the runs on the wall with tape before committing, so you can judge the lines from guest seats.

That depends entirely on your lease and the building. Some landlords allow small fasteners in mortar joints, which can be repointed at move-out, but prohibit drilling into brick faces or coring through walls. Buildings with historic status may have further restrictions. Get approval in writing and share the planned routes with the landlord before work starts. If drilling is ruled out, ceiling drops, pole mounts and routes through back-bar millwork are good alternatives.

In most cases, adding or moving an outlet is work for a licensed electrician, and what is permitted depends on your local code. An electrician can often add a surface-mounted box at mount height fed by its own conduit, which removes the cord hanging to a floor outlet. Ask your TV installer whether they coordinate with an electrician or whether you should arrange one separately, and schedule both so the runs line up.

Outdoor walls add moisture, sun and temperature swings, so materials matter more than looks. Use components rated for outdoor use, seal any point where cable enters the building, and avoid low spots where water can collect in a raceway or conduit. Plan the run so the screen can be removed for winter or service without disturbing the cabling. A site survey should cover the patio separately from the indoor walls.

Ready when you are

Talk to a programming specialist

Tell us about your space and we will put together a tailored, no-pressure custom solution.

Free, no-pressure quote

Request a custom quote

Tell us about your space and a commercial programming specialist will follow up. No pressure, just a solution-focused conversation.

Photo by Max Vakhtbovych on Pexels.

Make every screen count

Talk to a commercial programming specialist and get a package built for your business.

Call nowGet a Quote